Were you searching for tips concerning A Step-by-Step Guide to Installing a Bathtub?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and often, tiling skills. Changing an old bath tub with a new one is additionally a moderately tough task. If the old tub is conveniently accessible, the job can relocate speedily; if you need to open up a wall to remove the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. See to it you have actually qualified yourself for the job as well as fit trying it. As opposed to working with a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may need a professional plumber to make tube connections.
This short article will certainly aid you install a new tub in your restroom if you have actually currently gotten a brand-new bathtub as well as do not require to transform the setup of your previous water pipelines.
Your devices as well as product list must consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Secure the faucet in position with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the tub in the called for setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bathtub up until the level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the supply of water and check all joints as well as brand-new pipework for leakages and also tighten them if required. Fill up the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and securing around the bath tub should wait till the bath tub has actually been made use of a minimum of once as this will settle it right into its last placement.
Planning for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, bring about problems with dampness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack relatively early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about Installing A Bathtub. Thank you for finding the time to browse our content. Are you aware of someone else who is intrigued by the topic? Please feel free to promote it. I praise you for your time. Come back soon.
Rates